Cummins Insite 7.6

Cummins Insite 7.6

is a PC-based software application that provides quick and easy access to your engine’s electronic performance information, which enables faster service turn around times. INSITE helps to ensure accurate procedures and diagnosis and limit downtime, while increasing productivity and profits.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
New Features for INSITE™ 7.6
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Note: If it is difficult to read this document with Microsoft Notepad,
click on “Word Wrap” under the “Format” menu item or ‘maximize’
the Notepad window. To print this and have the tables in a valid
format set the page margins to 0.25.

See INSITE™ Release Notes for issues with the current and previous
releases.

************************************************************************
– The latest INLINE 6 drivers and firmware MUST be installed to use with
INSITE 7.6. They can be downloaded from the INLINE website:
http://inline.cummins.com/downloads/i6driver.html
************************************************************************

It is recommended after installation to register the INSITE™ PCID
displayed when logging into the Limited User account. Contact the
local Cummins Distributor to register your new INSITE™ and receive
a Basic Registration and Functional Level Password.

The latest INSITE™ information can be found on the website
http://insite.cummins.com

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
NEW INSITE™ FEATURES
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– Installation upgrade capability
Upgrade from INSITE™ 7.5.X.

– The INTELECT folder now contains a INSITE Engine Feature file.
The individual engine help files have eliminated. The INSITE Engine
Feature file lists the help descriptions for the engines Features
and Parameters, Diagnostic Test and Advanced ECM Data help content.

– Audit Trail
The Audit Trail has been expanded to support up to 8 Audit Trail
entries. This only applies to products if supported by the calibration.

– ECM Key Off Time
The required key off time may be more than 30 seconds for some
products. If supported by the calibration, INSITE will display
the required key off time when users are prompted to turn the key off.
This time is also displayed under the Data Monitor / Logger in INSITE.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
New Product Support
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– Turbocharger Actuator – The Turbocharger can be calibrated by
INSITE by using the Programmable Datalink Device (PDD) option in
Calibration Selection.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Calibration Selection
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– Calibration Selection
The Calibration Selection has been redesigned to include a separate
section for Programmable Datalink Device (PDD) Calibrations such as
the Aftertreatment Device or Turbocharger. This will allow users
to bypass connecting to the ECM and download directly to a PDD.

– Network Drive Performance Improvement
A performance improvement has been implemented for reading
calibrations on network drives. This greatly reduces the time
INSITE spends when the “View Network Calibration Drives” is
selected in the Tools > Options > General menu.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
New Features and Parameters
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
***These will only be displayed if they are supported by the
calibration.

– Features and Parameters
The column widths will remain on the same between INSITE sessions.

– Anti-Lock Brake (ABS) Controller
This feature provides the capability to enable the Anti-Lock Brake
ABS) Controller.

– Cab PTO
This feature provides the ability to enable or disable the operation
of PTO from inside the cab.

– Fan Minimum Run Time
This feature provides the ability to set the minimum time that the
fan will run each time it turns on.

– Idle Shutdown Hot Ambient Air Temperature Automatic Override
This feature provides the ability to override the Idle Shutdown Hot
Ambient Air Temperature Override threshold.

– Parking Brake Interlock Type
This feature provides the ability to allow PTO when the Parking
Brake is off.

– Step Size Adjustment
This feature provides the ability to configure the amount of
increase and decrease in step size when adjusting the Maximum
Vehicle Speed using the Cruise Control Set / Resume switches
when the Smart Road Speed Governor feature is enabled.

– Transmission Neutral Interlock
This feature provides the ability for PTO to be turned on only
if the transmission is in neutral and disengages PTO when the
transmission is taken out of the Neutral position. This feature
does not apply when the transmission type is manual.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Advanced ECM Data
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– Advanced ECM Data
INSITE will only display Advanced ECM Data features if they are
supported by the calibration.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ECM Diagnostic Test
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– ECM Diagnostic Test
INSITE will only display ECM Diagnostic Tests if they are
supported by the calibration.

– Fuel Injector Performance Test
This will test all fuel injectors at multiple predetermined fuel rail
pressures by monitoring the pressure drops across individual injectors
at multiple test points. It will compare this data to the
pre-determined limits for each test point. A Passed or Failed result
will be displayed along with status for each applicable cylinder and
test points. This only applies to the ISX 12/11.9/15 CM2250.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Data Monitor / Logger
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– Data Monitor / Logger
The column widths will remain on the same between INSITE sessions.

– Out of Range Window
The Out of Range window has been removed.

– Limit Columns
The Upper and Lower limit columns have been modified to display the
Minimum Measured and Maximum Measured values read by INSITE while
the parameters are being monitored.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Work Orders
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– Templates
The ability to Print Preview a Template has been added to the right
click menu.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Languages Supported:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– English

Limited Translation:

– Chinese (Simplified)
– Danish
– Dutch
– Finnish
– French
– German
– Indonesian
– Italian
– Hungarian
– Japanese
– Korean
– Norwegian
– Polish
– Portuguese
– Romanian
– Russian
– Spanish
– Swedish
– Turkish

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Operating System Support
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

– Windows® 7 32-bit (Recommended) and 64-bit

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Recommended PC Requirements
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

COMPONENT REQUIREMENTS (Recommended for new hardware purchases)

Platform: IBM or 100% Compatible

Operating System: Recommend: Windows 7 (32-bit)

Processor: 2.0 GHz or greater dual-core

RAM Memory: 2 GB or greater

Hard Drive: 6 GB or greater available disk space

Media Device: DVD-ROM

Display: SVGA(1024 x 768 pixels) Color

Keyboard: 101 Key Enhanced

Pointing Device: WindowsTM Compatible Device

Multimedia: PCs that will be used for Virtual College training will
require multimedia and sound capability

Other Software: Adobe Acrobat Reader v8.0 or higher
Microsoft .NET Framework v4.0

Printer: WindowsTM Compatible

Internet connection: DSL / Broadband high-speed (optional for updates and QSOL)

Available Ports: Two USB 2.0

Other: Refer to http://insite.cummins.com for latest information

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Minimum PC Requirements
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

COMPONENT REQUIREMENTS (for minimum performance)

Platform: IBM or 100% Compatible

Operating System: Supported: Windows® XP SP3 or greater, Windows® Vista, and
Windows® 7 32- and 64-bit versions for all operating systems
Note: Windows 7 Virtual PC and XP Mode are not supported

Processor: Windows 7 – 2 GHz

RAM Memory: Windows 7 – 2GB

Hard Drive: 2 GB available disk space

Media Device: DVD-ROM (may be internal or external as needed for installation)

Display: SVGA(1024 x 768 pixels) CRT
LCD: TFT Active Matrix, XGA (1024 x 768)

Keyboard: 101 Key Enhanced

Pointing Device: Windows® Compatible Device

Multimedia: Any Windows Compatible Sound Device

Other Software: Adobe Acrobat Reader v7.0 or higher
Microsoft .NET Framework v4.0

Printer: Windows Compatible Device

Internet connection: None

Available Ports: See datalink adapter manufacturer for port specifications.

Other: Refer to http://insite.cummins.com for latest information

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JRE Created: INSITE™ 7.6 October 2012
Document 6733-NEWF-07 Version 1.0.1
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

see more

http://www.arabtruck.info/phpbb/viewtopic.php?f=5&t=203

One thought on “Cummins Insite 7.6

Leave a Reply

Your email address will not be published. Required fields are marked *